Then, Vfb climbs up in a similar manner to the over load situation, forcing the preset maximum current to be supplied to the SMPS until the over load protection is activated. In order to avoid undesired activation of OVP during normal operation, Vcc should be designed to be below 19V. In order to avoid this undesired operation, the over load protection circuit is designed to be activated after a specified time to determine whether it is a transient situation or an overload situation. The articles, pictures, news, opinions, videos, or information posted on this webpage excluding all intellectual properties owned by Alibaba Group in this webpage are uploaded by registered members of Alibaba. Because of the pulse-by-pulse current limit capability, the maximum peak current through the Sense FET is limited, and therefore the maximum input power is restricted with a given input voltage.

Uploader: Salkree
Date Added: 26 February 2009
File Size: 41.24 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 52298
Price: Free* [*Free Regsitration Required]

If the sensing resistor voltage is greater than the AOCP level for longer than ns, the reset signal is applied to the latch, resulting in the shutdown dm055r SMPS. If the voltage of this pin reaches 6. If the items are defective, please notify us within 3 days of delivery.

Integrated Circuit IC DMR 1MR

Over load protection t Normal operation Fault situation Normal operation Figure 6. The supplier supports Trade Assurance — A free service that protects your orders from payment to delivery. This pin is the positive supply voltage input.

Because these protection circuits are fully integrated into the IC without external components, the reliability can be improved without increasing cost. The voltage across the resistor is then compared with a preset AOCP level. If return ,buyer need to return the goods within 45days.


As the load decreases, the feedback voltage decreases. In this situation, the protection circuit should be activated in order to protect the SMPS. It is designed to drive the transformer directly.

Assuming that the 0. If you are suspect of any unauthorized use of your intellectual property rights on this webpage, please report it to us at the following: In this generation the startup resistor is replaced by an internal high voltage current source.

Integrated Circuit 1M0565R

However, even when the SMPS is in the normal operation, the over load protection circuit can be activated during the load transition.

This event typically happens when the input voltage is increased or the output load is decreased. This zener diode also increases the immunity against line surge.

Fm0565r this manner, the auto-restart can alternately enable and disable the switching of the power Sense FET until the fault condition is eliminated see figure 6.

FSDMR employs current mode control, as shown in figure 5. Gold Plus Supplier The supplier supports Trade Assurance — A free service that protects your orders from payment to delivery. Donpv 46 inch lcd power supply board 4h. At startup, the dm0565g high voltage current source supplies internal bias and charges the external capacitor that is connected to the Vcc pin.

Since D1 is blocked when the feedback voltage Vfb exceeds 2. Once the fault condition occurs, switching is terminated and the Sense FET remains off. If needed,pls contact us for specific prices. The PWM controller includes integrated fixed frequency oscillator, under dm05565r lockout, leading edge blanking LEBoptimized gate driver, internal soft start, temperature compensated precise current sources for a loop compensation and self protection circuitry.


Supplier Types Trade Assurance. In order to rm0565r undesired activation of OVP during normal operation, Vcc should be designed to be below 19V. Crab kingdom dc 12v10a switching power supply board power supply module board power supply module transformer CN In order to prevent this situation, an over voltage protection OVP circuit is employed.

Dmr Transistor, Dmr Transistor Suppliers and Manufacturers at

The delay time for over load protection is designed to be about 50ms with C of 47nF. If the output consumes beyond this maximum power, the output voltage Vo decreases below the set voltage.

Lev voltage on the output capacitors is progressively increased with the intention of smoothly establishing the required output voltage. Temp Feedback Source Current vs. After startup, there is no power loss in these resistors since the startup pin is internally disconnected after startup.